How to Replace a Tub Yourself: Removing and also Replacing.
How to Replace a Tub Yourself: Removing and also Replacing.
Blog Article
The content listed below on the subject of How to Install a Bathtub Yourself is indeed motivating. You should see for yourself.
Mounting a bathtub isn't exactly brain surgery, however it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately hard task. If the old tub is readily easily accessible, the job can move easily; if you need to open a wall surface to eliminate the old tub and place the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to vacate the old tub and set in the brand-new one. Make certain you have certified on your own for the task and also fit attempting it. As opposed to working with a specialist to take over a halfway-completed task, it is better to consider using one before you begin. Possibilities are you may require an expert plumber to make tube links.
This post will aid you set up a brand-new tub in your shower room if you have actually currently purchased a brand-new tub as well as do not need to transform the arrangement of your previous water system pipes.
Your tools and also material checklist must consist of the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The process of getting rid of the existing taps can be rather bothersome due to the limited access that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any old securing substance.
Prior to proceeding to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Protect the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of the two wooden boards under its feet, place the bathtub in the needed setting. The wooden boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and adjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile tap connector to the suitable supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the water supply and examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub and also check the overflow outlet and also the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the tub ought to wait till the tub has been used at the very least when as this will settle it into its last placement.
Preparing for the Installment
Firstly, the sustaining structure supplied with the bath must be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can crack fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece on Installing A Bathtub while surfing the web. Are you aware of somebody else who is looking into A Step-by-Step Guide to Installing a Bathtub? Feel free to share it. Many thanks for going through it.
Estimating Report this page